Experimental investigations the effects of dusty, humidity and temperature conditions on chemical anchors
DOI:
https://doi.org/10.7764/RDLC.22.3.613Keywords:
chemical anchor, pull-out test, dust, humidity and temperature effects, ACI 318.Abstract
Chemical anchor applications are frequently used to add new structural elements to existing structures. Chemical anchors can be applied quickly and easily, if anchors apply according to a detailed installation and cleaning procedure depending on environmental conditions and workmanship. In this work, the relationship between the axial tensile capacity of chemical anchors and the effect of dust, humidity, and temperature were examined as adverse conditions. The effect of using different conditions, anchorage diameters and embedment depth on the tensile strength of the anchors was evaluated. In the experimental study, anchors diameter 12, 16 and 20 mm were selected to be used as anchors. The depth of embedding was determined to be 5, 10, 15 and 20 times the diameter of used anchors. The initial stiffness, displacement ductility ratio, energy absorption capacity, failure modes, and safety levels according to ACI 318 were obtained by using the load-displacement curves. According to the parameters considered in the experimental program, the most unfavorable situation was obtained in anchors embedded in a wet environment. In addition, it was observed that the diameter of the drilled holes causes a decrease in the axial tensile capacity by increasing the exposure time of the anchors to water and temperature.
Downloads
References
ACI 318. (2019). Building code requirements for structural concrete (ACI 318-19) and commentary. American Concrete Institute.
ASTM E488-96. (2003). Standard test methods for strength of anchors in concrete and masonry elements.
Ba, G., Weng, X., Liu, C., & Miao, J. (2021). Bond strength of corroded reinforcements in concrete after high-temperature exposure. Construction and Building Materials, 270, 121400.
Bajer, M., & Barnat, J. (2012). The glue–concrete interface of bonded anchors. Construction and Building Materials, 34, 267-274.
Bokor, B., Sharma, A., & Hofmann, J. (2022). Experimental investigations on the concrete edge failure of shear loaded anchor groups of rectangular and non-rectangular configurations. Experimental investigations on the concrete edge failure of shear loaded anchor groups of rectangular and non-rectangular configurations, 222, 111153.
Cook , R. A., & Konz, R. C. (2001). Factors Influencing Bond Strength of Adhesive Anchors. Factors Influencing Bond Strength of Adhesive Anchors, 98(1), 76-86.
Cook, R. A. (1993). Behavior of chemically bonded anchors. Journal of Structural Engineering, 119(9), 2744-2762.
Çalışkan, Ö., & Aras, M. (2017). Experimental investigation of behaviour and failure modes of chemical anchorages bonded to concrete. Construction and Building Materials, 156, 362-375.
Çalışkan, Ö., Yılmaz, S., Kaplan, H., & Kıraç, N. (2013). Shear strength of epoxy anchors embedded into low strength concrete. Construction and Building Materials, 38, 723-730.
Eligehausen , R., & Balogh, T. (1995). Behavior of Fasteners Loaded in Tension in Cracked Reinforced Concrete. Structural Journal, 92(3), 365-379.
Eligehausen, R., Cook, R. A., & Appl, J. (2006). Behavior and Design of Adhesive Bonded Anchors. ACI Structural Journal, 103(6), 822-831.
Epackachi, S., Esmaili, O., Mirghaderi, S. R., & Behbahani, A. T. (2015). Behavior of adhesive bonded anchors under tension and shear loads. Journal of Constructional Steel Research, 114, 269-280.
Gross, H. J., Klingner, R. E., & Graves, H. L. (2001). Dynamic Behavior of Single and Double Near-Edge Anchors Loaded in Shear. Structural Journal, 98(5), 665-676.
Hamad, R. J., Johari, M. M., & Haddad, R. H. (2017). Mechanical properties and bond characteristics of different fiber reinforced polymer rebars at elevated temperatures. Construction and Building Materials, 142, 521-535.
Henin, E., Tawadrous, R., & Morcous, G. (2019). Effect of surface condition on the bond of Basalt Fiber-Reinforced Polymer bars in concrete. Construc-tion and Building Materials, 226, 449-458.
Higgins, C. C., & Klingner, R. E. (1998). Effects of Environmental Exposure on the Performance of Cast-In-Place and Retrofit Anchors in Concrete. Struc-tural Journal, 95(5), 506-517.
Hlavička, V., & Lublóy, É. (2018). Concrete cone failure of bonded anchors in thermally damaged concrete. Construction and Building Materials, 171, 588-597.
Kalthoff, M., & Raupach, M. (2021). Pull-out behaviour of threaded anchors in fibre reinforced ordinary concrete and UHPC for machine tool construc-tions. Pull-out behaviour of threaded anchors in fibre reinforced ordinary concrete and UHPC for machine tool constructions, 33, 101842.
Kim, J.-S., Jung, W.-Y., Kwon, M.-H., & Ju, B.-S. (2013). Performance evaluation of the post-installed anchor for sign structure in South Korea. Perfor-mance evaluation of the post-installed anchor for sign structure in South Korea, 44, 496-506.
Li, T., Zhu, H., Wang, Q., Li, J., & Wu, T. (2018). Experimental study on the enhancement of additional ribs to the bond performance of FRP bars in concrete. Construction and Building Materials, 185, 545-554.
Li, Y., Yin, S., Lu, Y., & Hu, C. (2020). Experimental investigation of the mechanical properties of BFRP bars in coral concrete under high temperature and humidity. Construction and Building Materials, 259, 120591.
Ma, G., Huang, Y., Aslani, F., & Kim, T. (2021). Tensile and bonding behaviours of hybridized BFRP–steel bars as concrete reinforcement. Construction and Building Materials, 201, 62-71.
Maranan, G. B., Manalo, A. C., Karunasena, W., & Benmokrane, B. (2015). Pullout behaviour of GFRP bars with anchor head in geopolymer concrete. Composite Structures, 132, 1113-1121.
McVay, M., Cook, R. A., & Krishnamurthy, K. (n.d.). Pullout Simulation of Postinstalled Chemically Bonded Anchors. 122(9), 1016-1024.
Müsevitoğlu, A., Abdullah, M. H., Aksoylu, C., & Özkış, A. (2020). Ahmet. Measurement, 158, 107689.
Nilforoush, R., Nilsson, M., & Elfgren, L. (2017). Experimental evaluation of tensile behaviour of single cast-in-place anchor bolts in plain and steel fibre-reinforced normal- and high-strength concrete. Engineering Structures, 147, 195-206.
Obata, M., Inoue, M., & Goto, Y. (1998). The failure mechanism and the pull-out strength of a bond-type anchor near a free edge. Mechanics of Materi-als, 28(1-4), 113-122.
Pinoteau, N., Pimienta, P., Guillet, T., Rivillon, P., & Rémond, S. (2011). Effect of heating rate on bond failure of rebars into concrete using polymer adhe-sives to simulate exposure to fire. International Journal of Adhesion and Adhesives, 31(8), 851-861.
Porcarelli, S., Shedde, D., Wang, Z., Ingham, J. M., Giongo, I., & Dizhur, D. (2021). Tension and shear anchorage systems for limestone structures. Con-struction and Building Materials, 272, 121616.
Richardson, A. E., Dawson, S., Campbell, L., Moore, G., & Mc Kenzie, C. (2019). Temperature related pull-out performance of chemical anchor bolts in fibre concrete. Construction and Building Materials, 196, 478-484.
Rosa, I. C., Firmo, J. P., Correia, C. R., & Mazzuca, P. (2021). Influence of elevated temperatures on the bond behaviour of ribbed GFRP bars in concrete. Influence of elevated temperatures on the bond behaviour of ribbed GFRP bars in concrete, 122, 104119.
Shirvani, M., Klingner, R. E., & Graves III, H. L. (2004). Breakout Capacity of Anchors in Concrete Part 1: Tension. Structural Journal, 101(6), 812-820.
Stehle, E. J., & Sharma, A. (2021). Concrete cone breakout behavior of anchor groups in uncracked concrete under displacement-controlled cyclic tension load. Engineering Structures, 246, 113092.
Sun, W., & Ghannoum, V. M. (2015). Modeling of anchored CFRP strips bonded to concrete. Construction and Building Materials, 85, 144-156.
Takase, Y. (2019). Yuya. Engineering Structures, 195, 551-558.
Vita, N., Sharma, A., & Hofmann, J. (2022). Bonded anchors with post-installed supplementary reinforcement under tension loading – Experimental investigations. Bonded anchors with post-installed supplementary reinforcement under tension loading – Experimental investigations, 252, 113754.
Wang, Q., Zhu, H., Tong, Y., Su, W., & Zhang, P. (2021). Bond-slip behaviour of the CFRP ribbed bars anchored with the innovative additional ribs in concrete. Composite Structures, 262, 113595.
Yilmaz, S., Özen, M. A., & Yardim, Y. (2013). Tensile behavior of post-installed chemical anchors embedded to low strength concrete. Construction and Building Materials, 47, 861-866.
Zamora, N. A., Cook, R. A., Konz, R. C., & Consolazio, G. R. (2003). Behavior and Design of Single, Headed and Unheaded, Grouted Anchors under Tensile Load. Structural Journal, 100(2), 222-230.
Zhang, H., Smith, S. T., Gravina, R. J., & Wang, Z. (2017). Modelling of FRP-concrete bonded interfaces containing FRP anchors. Construction and Build-ing Materials, 139, 394-402.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2023 Özlem Çalışkan, Murat Aras, Yılmaz Ağdağ
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
